|
|
Gas Cap with 1/32" Vent Hole
Item Nbr. A1243
This aluminum screw on gas cap fits old style "Coffin" and "Peanut" threaded gas tanks. It uses an O-ring as a seal. |
$25.00 |
|
|
Gas Cap with 10-32 UNF Vent Hole
Item Nbr. A1245
This aluminum screw on gas cap fits old style "Coffin" and "Peanut" threaded gas tanks. It uses an O-ring as a seal.The 10/32 bolt and lock nut are included. |
$28.00 |
|
|
Gas Cap with 1/8-27 NPT Vent Hole
Item Nbr. A1244
This aluminum screw on gas cap fits old style "Coffin" and "Peanut" threaded gas tanks. It uses an O-ring as a seal. The hose barb is included. |
$28.00 |
|
|
Gas Cap with .013" Vent Hole
Item Nbr. A1242
This aluminum screw on gas cap fits old style "Coffin" and "Peanut" threaded gas tanks. Cap has a sintered bronze vent fitting.It uses an O-ring as a seal. One only. |
$28.00 |
|
|
Frame, Fork Tube Bung
Item Nbr. A1194
This is a 3/8"-24 UNF tube weld bung for Rokon motorcycles. It will fit the rear wheel stays, the handle bar mounts and the front fork wheel stays. It is threaded all the way through. Cutting and welding required. |
$8.00 |
|
|
"Dogbone" Handle Bar Clamps
Item Nbr. A1195
This is a new CNC machined set of 6061-T6 aluminum handle bar clamps for a Rokon 2 wheel drive motorcycle with 7/8" diameter handle bars. The grade 5 bolts are included. They are machined to fit Rokon forks with a bolt spacing of 3 3/8" to 3 1/2". Please check your bolt centerline spacing before you purchase these bar clamps. I was able to get measurements from about 20 bikes and designed these clamps to fit. If you have something different...please let me know. The dogbone tops are designed to work with the 4 piece clamps that I already sell on my website. The tops will be available seperately on my website as soon as my wife gets them listed. |
$40.00
Out of Stock |
|
|
 |
#606 Woodruff Key
Item Nbr. A1196 |
$0.25 |
|
|
 |
5/8" to 3/4" Clutch Cdapter
Item Nbr. A1197
This is a new 5/8" to 3/4" clutch adapter for a Rokon with a 2 stroke motor. This will allow you to install a go kart or mini bike centrifugal clutch with a 3/4" bore on your Power Bee 2 stroke. It is too short to use with a Comet torque convertor. A step key should be used with this adapter. |
$7.00 |
|
|
Kickstart Eliminator Bushing
Item Nbr. A1101
This is a CNC machined bronze bushing designed to replace the kickstart assembly in an Albion transmission in a Rokon motorcycle. It has a press fit in the Albion side cover. There is also an endplay adjuster for the transmission countershaft. The transmision and or side cover are not included. |
$35.00
|
|
|
Salsbury 330 Torque Converter Nut
Item Nbr. A1198
This is a CNC machined nut that is used to attach a Salsbury 330 torque converter driver clutch to a West Bend, Chrysler Power Bee 820 motor in a 2 wheel drive Rokon motorcycle. These are used with the "Plunger" 3 speed transmissions and the 2 stroke Power Bee engines. it has a 7/16-20 UNF thread and a 3/4" hex just like the original units. It comes with a stamped steel retainer.
|
$15.00 |
|
|
Handle Bar Clamps
Item Nbr. A1199
Aluminum CNC machined handle bar clamps with bolts for 7/8" diameter handle bars. |
$30.00 |
|
|
Mercury Clutch Seal
Item Nbr. A1200
This is the correct seal for a Mercury centrifugal clutch as used on a Rokon. |
$4.00 |
|
|
Mercury Clutch Small Parts Kit
Item Nbr. A1201
This kit includes 2 seals, both snap rings, and 2 brass shims. The brass shims are the same size as the original Micarta shims. |
$10.00 |
|
|
Mercury Clutch Retaining Nut (extended)
Item Nbr. A1205
This is an extended CNC machined 304 stainless steel nut that is used to fasten a Mercury centrifugal clutch to a Chrysler West Bend Power Bee 820 engine in a Rokon 2 wheel drive motorcycle. The hex is 11/16" and the thread is 7/16-20 UNF right hand. It is 3/8" longer than stock so you do not have to use a special thinwall 11/16" socket to remove it. This will work with a boxwrench or a standard socket. This nut may interfere with the guard on your bike. Check if you have an extra 3/8" of clearance before you purchase one of these. The Mercury clutch is not included. |
$18.00
|
|
|
Mercury Clutch Retaining Nut
Item Nbr. A1144
This is a CNC machined 304 stainless steel nut that is used to fasten a Mercury centrifugal clutch to a Chrysler West Bend Power Bee 820 engine in a Rokon 2 wheel drive motorcycle. The hex is 11/16" and the thread is 7/16-20 UNF right hand.
|
$15.00 |
|
|
Valve Stem Protector
Item Nbr. A1206
This valve stem protector is used to keep the inner tube valve stem from disappearing on the 15" drum wheels when you are running low air pressure
|
$5.00
Out of Stock |
|
