|
|
#106 Miter Box Spacer
Item Nbr. A1179
This is a new .948" long spacer that goes behind the miter gear on the output shaft of a front or rear miter box with the bolt on end caps. |
$2.25 |
|
|
|
#107 Miter Box Spacer
Item Nbr. A1180
This is a new 1.344" long spacer that goes in front of the miter gear on the output shaft of a front or rear miter box with the bolt on end caps. |
$3.50 |
|
|
|
#108 Miter Box Spacer
Item Nbr. A1181
This is a new .847" long spacer that goes between the bearings on the driveline connector shaft of a front or rear miter box with the bolt on end caps. It is supplied with a 1/4-28 set screw.
|
$3.50 |
|
|
|
3 Bolt Miter Cap
Item Nbr. A1182
This new miter cap comes with 3 allen head cap screws. |
$21.00 |
|
|
|
4 Bolt Miter Cap
Item Nbr. A1183
This new miter cap comes with 4 allen head cap screws. |
$21.00 |
|
|
|
Miter Box Seal
Item Nbr. A1184
This is a new seal that fits both the screw in and bolt on cap miter boxes. |
$5.00 |
|
|
|
Early Miter Box Bearing
Item Nbr. A1185-86
This is a new miter box bearing (cone and cup) for an early Rokon with a miter box with threaded end caps. |
$8.00 |
|
 |
1/8" NPT Magnetic Plug
Item Nbr. A1187
This also fits the plunger transmissions.
|
$2.00 |
|
 |
.800" Early Miter Box Spacer
Item Nbr. A1188
This is a new .800" long spacer that goes between the bearings on the driveline connector shaft of a front or rear miter box with the screw on end caps. It is supplied with a 3/16" dowel pin. |
$4.00 |
|
|
|
.974" Early Miter Box Spacer
Item Nbr. A1189
This is a new .974" long spacer that goes behind the miter gear on the output shaft of a front or rear miter box with the screw on end caps. |
$4.00 |
|
 |
1.380" Early Miter Box Spacer
Item Nbr. A1190
This is a new 1.380" long spacer that goes behind the miter gear on the output shaft of a front or rear miter box with the screw on end caps.
|
$4.00 |
|
|
|
3/4" Axle/Miter Box/Plunger Transmission Bearing
Item Nbr. A1171
This is a new sealed bearing for a 3/4" axle, miter box or a Plunger transmission. This fits the bolt on cap miter boxes. |
$6.00 |
|
 |
Extended Rear Miter Box Shaft
Item Nbr. A1139
This is a new CNC machined extended rear miter box shaft for a 2 wheel drive Rokon motorcycle. This will allow the installation of a rear disk brake. It works with a standard keyed output sprocket, but it will need a new keyed input sprocket or you will have to have a keyway and set screw hole installed in your existing pinned input sprocket. This shaft is also keyed for the miter gear. The brake rotor uses the same key as the input sprocket. The shaft is 9 inches long. 2 new #606 keys, a 3/16 inch diameter split pin and a 3/16 inch square key are included. This will not work in a "Plunger" transmission or a front miter box. |
$25.00
|
|
 |
Front Brake Conversion Kit
Item Nbr. A1191
These are the parts needed to install a disk brake shaft in a Nethercutt/Early Rokon miter box that has a solid cap on one side. The shaft, O-ring style screw in cap, O-ring, seal, keys, and roll pin are included. The brake disk is NOT included. The shaft will work with the original pinned miter gear or a pinned & keyed miter gear. |
$40.00 |
|
|
|
Front Miter Shaft
Item Nbr. A1131
This is a new CNC machined Rokon front miter shaft that is keyed for the output sprocket instead of pinned. This allows use of an off the shelf sprocket. This shaft is also keyed for the miter gear. |
$25.00 |
|
 |
Rear Miter Box
Output Shaft for Locked Overrides
Item Nbr. A1138
This is a new CNC machined rear miter box output shaft for a 2 wheel drive Rokon motorcycle. This is the shaft that connects to the override clutch inside the main frame tube. This works with the locked override that I also have available. The shaft is 4 9/16 inches long. 4 new 3/16 inch diameter split pins are included. This will not work in a "Plunger" transmission or a front miter box. |
$15.00 |
|
 |
Rear Miter Box Output Shaft
Item Nbr. A1137
This is a new CNC machined rear miter box output shaft for a 2 wheel drive Rokon motorcycle. This is the shaft that connects to the override clutch inside the main frame tube. This works with the original unlocked override clutches. The shaft is 5 5/8 inches long. 2 new 3/16 inch diameter split pins are included. This will not work in a "Plunger" transmission or a front miter box. This shaft is keyed for the miter gear. |
$15.00 |
|
